1. Oki B4400 Printer Triangle Flashing
2. Oki B4400 Printer Flashing Light Triangle
3. Oki B4400 Printer Triangle Flashing Light

Brendan Howe, President and CEO of TDCNet, speaks about a few simple steps on fixing printing problems quickly. Triangle with! Blinking what does it mean? - OKI B4400 Printer question. Oki B4400 Error Messages. User Manual: Troubleshooting; Status And Error Messages; Paper Jams Oki priner user's guide. Drum beat program free download. Hide thumbs Also See for B4400 Series Guide.

What you will see Unwanted spots or streaks of toner are appearing on the front or back sides of the printed page. Possible causes In most cases, the cause of this issue will be either the toner cartridge or the photoconductor unit. Follow the instructions below. Check/replace the supply items Step Action 1 Before you check the printer supplies, try printing on plain 20 - 24 lb copy paper if you are not already doing so. This will eliminate any special print media as part of the cause of the problem. Please try this even if the print media you are currently using has worked in the past. Certain specialty papers, such as letterhead stock, label stock, and light card stock, do not allow toner to adhere as well as plain paper.

This is especially true of media that is textured or has a rough surface. 2 Once you have eliminated the paper/print media as part of the cause, power off the printer and remove the toner cartridge. The toner cartridge is accessed by opening the upper front cover of the printer. 3 Install another toner cartridge into the printer.

Use one of the methods listed below. • Replace the existing toner cartridge with a brand-new toner cartridge, if you have one available.

Oki B4400 Printer Triangle Flashing

NOTE: This is the recommended action to take whenever possible. • If this is a newly installed toner cartridge, reinstall the cartridge you removed when you installed the new one. • Install a toner cartridge from another Lexmark E120 series printer which is printing correctly.

4 Power the printer back on. 5 Try printing again. Print 20 to 30 pages with a small amount of print on each of them. This will give the spots/streaks a chance to clear up. If a different toner cartridge corrects the issue, the printer is fine and the problem is with the first toner cartridge.  Kakao log in. Please carry out the following checks on the cartridge: • Confirm that you are using an original Lexmark brand toner cartridge. If a third-party cartridge is causing this issue, please contact the point of purchase to have the cartridge replaced. • Confirm that the toner cartridge has not been refilled or reworked in any way.

Oki B4400 Printer Flashing Light Triangle

Refilling the toner cartridge can damage it, which can cause print quality issues of this kind. If the cartridge has been refilled or reworked, contact the place where it was refilled to have it replaced. • If this is an original Lexmark toner cartridge, inspect it for any damage or defects. If you notice any damage to the cartridge, please contact. Your toner cartridge may be eligible for replacement, depending on how old or used it is. If the toner cartridge does not appear to be damaged but is relatively new or unused, it may still be eligible for replacement. Please contact the point of purchase first as they may have a replacement policy.

Oki B4400 Printer Triangle Flashing Light

If the cartridge was purchased directly from Lexmark, contact Lexmark using the phone number or address you used to order the cartridge. If the point of purchase cannot assist you or if you cannot locate the number you used to contact Lexmark to order the cartridge, contact Lexmark Technical Support. A representative there may be able to provide more assistance. 6 If the issue occurs on more than one toner cartridge, power off the printer and remove the photoconductor assembly. The photoconductor assembly is accessed by opening the rear cover of the printer. 7 There will be a blue or green color roller on the photoconductor assembly. Check the condition of the surface of this roller.

• If any part of this roller's surface is scratched or otherwise damaged, replace the photoconductor assembly and try printing again. • If the roller appears dirty, take a dry, lint-free cloth and carefully clean off the surface of the roller. Take care not to touch the surface of the roller with your bare fingers as that may leave a permanent mark on the roller. Once the roller is clean, reinstall the photoconductor assembly, power on the printer, and try printing again. 8 If the issue continues after you have carried out all of the above checks, the printer may require a service action.